Multi-line 2 Utility Software v.3.x.

3.59.1

04/04/2024

USW3 build revision: 2851

USW3 product database revision: 10229

Corrections

• Correction to permissions write during batch write.
• AOP-2 emulated button corrected.
• M-Logic delay timer was not written to the controller.
• M-Logic items in use showing wrong counting.
• M-Logic and AOP in use button not showing active M-Logic lines with offline files.
• M-Logic and AOP in use button showing wrong interpretation for Virtual event output.

3.59.0

12/02/2024

USW3 build revision: 2814

USW3 product database revision: 10079

New features

• Added separate page for ECU and DVC configuration.

Improvements

USW performance improvements:

• M-Logic & AOP handling.
• .Trend file handling.
• Parameter tree structure.
• Alarm update in USW.
• USW message pop-up.
• Batch read and write.
• Offline file handling.

3.58.0

22/12/2023

USW3 build revision: 2752

USW3 product database revision: 9675

New features

• Added support for AGC 150 – 1.18.0.
• Added support for ASC-4 – 4.27.0.
• Added support for AGC-4 Mk II – 6.12.0.

3.58.0

22/09/2023

USW3 build revision: 2752

USW3 product database revision: 9374

New features

• Added data logging status.
• Added dynamic table for PMS lite application supervision.
• Dynamic parameter based on configurational value to show relevant parameters.

Corrections

• Improved batch write function.
• Fixed translation issues.
• Fixed issue with opening general purpose PID.

3.57.1

07/09/2023

USW3 build revision: 2715

USW3 product database revision: 9215

Corrections

•  Batch read and write fixed
• Other bugs fixed

3.57.0

10/07/2023

USW3 build version: 2686

USW3 product database revision: 9157

New features

• Added offline configuration comparison tool.
• Added new device page for PMS Lite.
• Added new application supervision for PMS Lite.
• Added option to open and save sensor curve file in AGC 150 Engine drive, AGC 150 Engine drive marine, AGC 150 Generator marine, AGC 4 Mk II Genset.

Corrections

• Fixed access violation error when function keys F4 and F5 are pushed too quickly.

3.56.0

27/02/2023

USW3 build version: 2516

USW3 product database revision: 8789

New features

• Live value available from the "Parameters" page in tree view mode.
• New translation files are added to the translation folder.

Changes

• Moved "Permissions" icon to the left menu under "Tools". It is still called "Permissions".
• Moved "PID Configuration" icon to the left menu under "Tools". Renamed to "General Purpose PID”.
• Moved "Modbus Configuration" icon to the left menu under "Tools". The name is the same.
• Added "Firmware" to the "Option" page. Renamed "Option" to "Option & firmware”.
• "Device Information" is now available from the "Option & firmware" page.
• Optimised the tree view text.
• Moved "N-Option" icon to the left menu under "Tools". Renamed to "Ethernet Setting (Modbus TCP/IP)".
• Changed "Open & Close" hyperlink to button icon.
• Changed the maximum number of languages for AGC 150 to 8.
• Moved "Translations" from "Configuration" to "Tools".

Corrections

• Optimised the menu bars and windows.
• Optimised the connection with the controller.
• Fixed "Write to plant" function.
• Fixed sensor scaling and curve for multi-input AGC 150 DG.

3.55.1

09/01/2023

USW-3 build version: 2457
USW-3 product database revision: 8666

New features

• Selective reading/writing of M-Logic and AOP.
• CIO configuration moved from pop-up to a dedicated page.
• Parameter tree view improvements:
  • Collapsible panels
  • Search function
  • Parameter number
  • Tree structure improved
• New pop-up for disconnect function.
• Support of 5 CIO 308 modules for AGC-4 Mk II.
• Support of 5 CIO 208 modules for AGC-4 Mk II.
• Support of 5 CIO 116 modules for AGC-4 Mk II.
• Multi-input: Added selection for the number of points in the configurable sensor curve.
• Multi-input: Changed open & close text hyperlink to button.
• Translation folder created in app data location with language files.

Changes

• Updated sensor files.

Corrections

• Every time advanced protection parameters are read, the USW reports that the connection timed out.
• Question marks in I/O setup from old controller.
• USW disconnects when another power management unit is missing.
• Code ANSI zero sequence current/voltage corrected in mouse-over text for parameters.
  
  

3.54.1

21/10/2022

USW3 build version: 2362
USW3 product database revision: 8516

Changes:

- USW Connection Handling.
- Sensor curve open & close hyperlink text colour.
- RMI Type Selection in multi-input available again.

Corrections:

- Enhanced performance for "Inverterdata".
- AGC-4 Mk II function drop-down disabled for breaker feedback.
- RMI Scaling in multi-input fixed.

3.54.0

09/09/2022

USW3 build version: 2320.
USW3 product database revision: 8363.

New features:

• Support of AGC 150 – 1.12.0
• Support of ASC-4 – 4.23.0

3.54.0

29/08/2022

USW3 build version: 2320
USW3 product database revision: 8322

New Feature

• Added provision to edit and save sensor curves for multi Inputs and CIO
• Added pre-defined sensor curve
• New launcher window

Changes

• Left-side navigation menu style
• Change symbol in USW

Corrections

• Batch write crash issue.
• Russian language.
• USB driver signing issue.
• M-logic will overwrite other saved items

3.53.0

30/06/2022

USW3 build version: 2186.
USW3 product database revision: 8174.

Changes:

• Support of AGC 150 – 1.11.0
• Support of ASC-4 – 4.22.0
• Support of AGC-4 Mk II – 6.07.0
• New Launcher page for selected products.
• New Menu bar for selected products.
• Ability to save and load sensors via customer files

3.53.0

25/04/2022

USW3 build version: 2186

USW3 product database revision: 7957

New features:

• Added Portuguese (Brazil) localization.
• Reduced repeated lists on the Product Database.
• Button to open/close the M-Logic toolbox.

Changes:

• New ProductIDs in USW V.3.53.0.
• Russian language for Views.

Corrections:

• USW crashing with Floating-point overflow.
• Expand buttons disappear when using "Copy to the line below" (AGC 4 and AGC150).
• Mismatch column in parameter tab is not present corrections.
• Parameter disappears after changing Parameter 7841.
• Spinedit component resolution does not respect the decimals attribute.

3.52.0

22/02/2022

USW3 build version: 2123.
USW3 product database revision: 7880.

New features:

• Added Support for IEEE 1547 on selected controllers.
• Added fields to Identifiers window to meet dataplate requirements of IEEE 1547.
• Added configuration parameters and their graphical representation on the Advanced Protections page.
• Added parameter validation to meet the configuration requirements of IEEE 1547.

Changes:

• Changed graph component to support new features and requirements.
• Changed spinedit component to support new features and requirements.
• Identifiers window content is now always read when opening the window.
• Identifiers window now asks for confirmation when it is being closed.

Corrections:

• Fixed an issue causing the Inverter Data page to freeze when opening.
• Fixed an issue where the slider value would work irregularly.
• Fixed an issue that caused a crash when the IP address was not available.
• Fixed an issue for an illegal data value error when writing Multi-Inputs.
• Fixed an issue that caused the language selection to not be available.
• Fixed an issue where setpoint 3 was not available for RMI inputs.

3.51.0

16/02/2022

USW3 build version: 1978.
USW3 product database revision: 7845.

New features:

• Support of AGC 150 – 1.10.0
• Support of ASC-4 – 4.21.0
• Support of AGC-4 Mk II – 6.06.0

3.51.0

16/12/2021

USW3 build version: 1978.
USW3 product database revision: 7679.

New features:

• Support of AGC 150 – 1.09.0
• Support of ASC-4 – 4.20.0

3.51.0

11/11/2021

USW3 build version: 1978.
USW3 product database revision: 7621.

New features:

• Support for PMS redundancy on AGC 150.
• Support for AGC 150 Remote Display variant.
• Support for AGC 150 Marine.

Changes:

• The device page for AGC 150 Hybrid now shows values for the inverter.
• The supervision page for AGC 150 Hybrid now shows a generator with a PV panel.

Corrections:

• Solves an issue that made it difficult to edit numeric fields.
• Solves an issue that made toolbars seem to not be present.
• Solves an issue that caused corruption to special characters on export of Translations to a CSV file.
• Solves an issue on I/O Setup occurring when opening a .usw file of AGC 150 and AGC-4 Mk II.
• Solves reported issues of support for special character handling in several pages.
• Solves an issue leading to errors in the graphs of the VRT tabs in Advanced Protections.

3.50.1

07/07/2021

USW3 build version: 1880
USW3 product database revision: 7366

Corrections:

• Fixed an issue that prevented users from scaling the multi-inputs.

3.50.0

09/06/2021

USW3 build version: 1849
USW3 product database revision: 7312

Changes:

• Validation of CIO 208 configuration written to the controller
  
  • In some cases, the controller may reject the configuration set by the user.
  • The Write function now reads back from the controller and notifies the user in case of disparity between the user selections and the controller.

Corrections:

• Fixed an issue causing failures to read the CIO configuration in Batch Read.
• Fixed an issue where some drivers had a wrong digital signature.
• Fixed an issue where multi-input scaling would change back to "DegC 1/1" after writing to the controller.
• Fixed an issue where Batch Read and Batch Write would not work properly for Multi-input settings.
• Fixed an issue where the RMI configuration would be lost when using the Batch Write functionality.
• Fixed an issue where the Batch job would finish but the pop-up would not accurately depict the progress.
• Other small fixes and performance improvements.

3.47.2

28/04/2021

USW3 build version: 1808.
USW3 product database revision: 7240.

What's new:

Support of AGC150 – 1.06.0.

New features:

• Added AGC150 Engine drive variant.
• Added fallback timer for power limit on SunSpec (parameter 17180).
• Added support for Keyswitch in I/O setup.
• Added support of PV breaker.
• Added EIC and MPU speed to delta alarms.

3.47.2

25/03/2021

USW3 build version: 1808.
USW3 product database revision: 7181.

What's new:

Support of AGC-4 – 4.81.0
Support of AGC-4 Mk II – 6.02.0
Support of ASC-4 – 4.16.0

Corrections:

• Solves an issue where importing favorites was not working.
• Solves an issue where errors would occur when the PC awakes from sleep mode.
• Solves an issue where the parameters from Advanced Protections would not be consistently written to the controller.
• Solves an issue where AOP 1 and AOP 2 would be written when cancelling the write operation of M-Logic.
• Solves an issue where an Access Violation error would occur when writing to multiple controllers.
• Solves an issue where the "Enable" parameter was not written when writing to multiple controllers.
• Solves an issue where the IP address would disappear from the bottom status line on some controller types.
• Solves an issue where the CIO 116 and CIO 208 could not be configured.
• Solves an issue where an error would occur when selecting CIO 116 on some controllers types.

3.47.1

12/01/2021

USW3 build version: 1743.
USW3 product database revision: 6991.

What's new:

  • AGC-4 Mk II release:
  • Support for Application SW download.
  • New bootloader available for AGC-4 Mk II.

  • New I/O setup page for AGC 150 and AGC-4 Mk II:
  • The I/O configuration toolbar button and respective page have been deprecated for the mentioned products.
  • The input alarm and relay configuration functions have been removed from the parameter list for the mentioned products.
  • Digital input and multi-input functions and alarms are now placed in tabs on the I/O setup page, accessible from the main navigation menu on the right side of the window.
  • Output functions and configuration are now placed in a single tab on the I/O setup page.

  • CIO input/output function setup:
  • Due to the removal of the I/O configuration pop-up, CIO116 and CIO208 functions can be selected in the CIO configuration page.
  • The support for functions on CIO308 multi-inputs is not supported by this release.

3.45.4

03/09/2020

USW3 build version: 1518
USW3 product database revision: 6586

What's new:

• Adds support of upcoming AGC 150 Hybrid.
• Adds support of upcoming AGC-4 version 4.79.0.
• Adds support of upcoming ASC-4 version 4.14.0.

Corrections:

• Solved issue with CIO alarm setpoint shown as zero.
• Solved issue where AGC 150 multi input alarm delays were possible to set outside the allowed range.

3.45.3

27/03/2020

USW3 build version: 1490
USW3 product database revision: 6360

New:

• Adds support of upcoming AGC 150 version 1.02.0.
• Adds support of upcoming AGC 150 version 1.03.0.
• Adds support of upcoming AGC-4 version 4.77.0.
• Adds support of upcoming ASC-4 version 4.12.0.

3.45.2

17/12/2019

USW3 build version: 1471
USW3 product database revision: 6257

New:

• Adds support of upcoming AGC-4 version 4.75.0.
• Adds support of upcoming AGC-4 version 4.76.0.
• Adds support of upcoming ALC-4 version 4.10.0.
• Adds support of upcoming AGC 150 version 1.01.0.

Corrections:

• Solves an issue where the Multi Input alarm inhibits from a stored usw-file, was changed to zero before written to the AGC 150.
• Solves an issue with wrong scaling on Multi Input: Alarm Set points for input types: PT100 and RMI Fuel level
• Solves an issue with wrong scaling on Multi Input: Curve Set points for input type = RMI Water temp.

3.45.1

29/08/2019

USW3 build version: 1439
USW3 product database revision: 6109

Corrections:

• Solves an issue where the firmware could not be downloaded to the AGC 150 via TCP/IP if the PC and the controller were not on the same subnet. 
• Solves an issue with wrong scaling on droop curve 2 parameters.

3.45.0

06/05/2019

USW3 build version: 1430
USW3 product database revision: 6024

New Features:

• Support for configurable 5 line display view in AGC 150 series. 
• Support for AGC 150.
  - Firmware update USB and LAN
  - Bootloader update
  - New Multi-Input setup page
  - New Navigation icons

• Support of ASC-4 Load Point connection in Power Management applications. 

Improvements:

• Commissioning view in Parameter removed when irrelevant to parameter 
• Trending settings are now allowed to be down to 20 ms (0.02s) polling.  
    - Note: Controller may not be able to deliver data at this rate.

Corrections:

• Solves an issue where the Log page would no read all log lines. 
• Solves an issue where plant read/write would fail in some occasions. 
• Fixes the command line parameter for Advanced protections. 
• Solves an issue introduced in USW v.3.44.0 where the "M-Logic and AOP items in use" window would not show all information. 
• Solves an issue where parameters could be missing in the batch (.usw) file. 
• Solves an issue introduced in USW v.3.44.0 where the AOP2 configuration could fail. 
• Solves an issue where Beckhoff modules outputs were missing on the GC-1F. 
• Solves an issue where the ASW is not shown when writing batch file on the AGC100. 
• Fixes the battery colour in Application Supervision. 

3.44.1

21/01/2019

USW3 build version: 1386
USW3 product database revision: 5778

Corrections

1. Advance protection Print and print preview 
2. Power management now showing in M-Logic & AOP Events
3. M-Logic offline file can be opened without connecting to controller
4. Sequence CIO and PID has been changed while batch writing 

3.44.0

06/12/2018

USW3 build version: 1372
USW3 product database revision: 5733

New Features:

• M-Logic & AOP
   - M-Logic and AOP configuration are now organised in tabs on the same page.
   - The AOP configuration pop-up is changed to work as an AOP mimic (ASW > 4.60.0).
   - Added a visual representation (diagram) of the logic blocks selected in the logic line.
   - Added a toolbar for easy drag-and-drop of Events and Outputs to the logic lines.
   - Dynamic M-Logic and AOP are now evaluated on the logic lines diagram.   
• Parameters - Sets of Favourites
   - Users can create/modify/delete sets of Favourites under the Settings page.
   - Users may Import/Export Favourites sets in settings under the Settings page.
   - Users can categorise parameters into different sets of Favourites.
   - Favourites filter has now a drop-down menu for selecting from the available sets of Favourites.
• Parameters – Parameter management
   - Users can now perform selective saving and writing of parameters.
   - A new indicator help users to identify parameters that were edited, but not written.
   - Users can now filtrate the parameter list for edited parameters.
• Advanced Protections configuration page for options A1, A10, C2 (ASW > 4.70.0)
• Command line 
   - It is now possible to merge parameter files with the command line interface.
   - Merged parameters can be written to a file or written directly to a controller.

Improvements

• USW is now an available application to select from on Windows side-by-side view.
• ALCs can now be added to the left of Mains.
• Performance improvements in reading parameters (after first read). 

Corrections

• Fix for batch read/write and backup/restore for PID settings and ID.
• M-Logic not displayed in USW3 under content in .usw file

3.43.2

27/09/2018

USW3 build version: 1236
USW3 product database revision: 5599

New

• Adds support of upcoming AGC-4 version 4.68.0.
• Adds support of upcoming AGC 200 version 4.68.0

3.43.2

12/06/2018

USW3 build version: 1236
USW3 product database revision: 5477

New

• Adds support to the upcoming release of ASC-4.11.0
• Adds support to the upcoming release of AGC-4.67.0

Improvements

• Changes the naming of output tab in parameters to ‘Outputs’

Fixes

• Fixes an issue in AGC 200 M-Logic where Ventilation mode and Dry mode were not working.

3.43.2

15/05/2018

USW3 build version: 1236
USW3 product database revision: 5368

Corrections:

• In some cases where the OS was localised, the utility software was wrongly showing a debug version message.

3.43.1

16/03/2018

USW3 build version: 1222
USW3 product database revision: 5368

New features:

• QR code for options upgrade
• Visual updates in application supervision
• Command buttons for DG units in supervision
• Click on unit to open its command panel
• Up to 8 configurable values may be added for each ID in supervision (only units configured on top or bottom of area)
• Sorting I/O in alphabetical order
• Duration of mouse-over texts is now configurable
• USW now stores the parameter view settings so that it opens in same view next time
• Support of AGC-4 version 4.66.0
• Support of ASC-4 battery controller

Changes:

• Various updates related to ALC-4
• Various updates related to ASC-4 PV

Corrections:

• In some situations, the USW would not show the correct application and breaker positions
• ASC Battery: When drawing a stand-alone application for ASC Battery with only the battery, the colours are wrong

3.42.0

12/10/2017

USW3 build version: 1164
USW3 product database revision: 5223

New features:

• Support of AGC-4 and AGC 200 version 4.65.0
• Support of new power meters on ASC-4

Corrections:

• Corrected: AGC 233 parameters not shown
• Corrected: Emulation in AGC 200 and AGC-4 not working

3.42.0

01/09/2017

USW3 build version: 1164 
USW3 product database revision: 5181

New features:

• Radio Ripple Control Receiver (RRCR) communication support for ASC-4/ASC PM
• Option N will create exceptions for firewall, but only if the user is admin. This will be handled in the installation file
• Includes reliability data in USW files
• Dynamic evaluation added to AOP-1 and AOP-2
• Navigation in the USW even when AOP window is open
• Text representing the regulator mode
• "Save All" files function on the USW
• Support of new ID configuration
• Shows SIPC number in USW3 when USW is built/used for an SIPC
• Possible to zoom in and out in the plant view
• Support of digital I/O in trending
• Support of trend only mode

Changes:

• Inverter data support updated for ASC-4, ASC PM
• Improved dialogue when changing between units 
• Application supervision unit ID on PV and LG
• CIO inputs column in the Inputs/Outputs list is made wider
• Possible to multiply the trending values so they match the CIO configuration

Corrections:

• Strange pop-up during connection to a genset group tie removed (build 1092)
• CIO added to OEM product IDs
• Unconfigured TB is no longer shown
• Corrected: Remote maintenance M-Logic missing (option H12)
• Translation no longer reveals passwords
• Option H13 added in option overview
• MB is no longer shown when opening a batch file when it is not present
• List of CIO 308 cold junction inputs is now updated when reconnecting the USW
• Unit scaling and RMI sensor type are aligned 
• Russian translation of RMI corrected
• "Active alarm log" can be pulled up again after minimising
• Dialogue box no longer keeps the existing M-Logic text
• M-Logic no longer disappears during batch reading
• AGC 100: Writing phone numbers with a batch write no longer results in strange characters
• Possible to write CIO parameters with batch file
• BTBs can no longer be misplaced in application drawings with ASC/ALC
• Power management ID selection logic corrected, when using new IDs
• M-Logic event C drop-down list now always opens
• Logged alarm values are now scaled correctly

3.41.2

03/04/2017

USW3 build version: 1119
USW3 product database revision: 4980

New features:

• Support of AGC 222 OEM variant

3.41.0

25/11/2016

This software applies to the following DEIF products:

• GC-1F v.1.xx
• Multi-line 2 - AGC v.3.xx
• Multi-line 2 - PPM v.3.xx
• Multi-line 2 - PPU v.3.xx
• Multi-line 2 - GPU v.3.xx
• Multi-line 2 - GPC v.3.xx
• Multi-line 2 - AGC 200
• GC-1F ATS
• GC-1F/2 v.2.xx
• Multi-line 2 - AGC v.4.xx
• Multi-line 2 - GPU-3 REC ver. 3.xx
• Multi-line 2 - AGC 100 v. 4.xx
• Multi-line 2 - CGC 200
• Multi-line 2 - CGC 400
• Multi-line 2 - ECU 100
• Multi-line 2 - GCU 100
• Multi-line 2 - PPU v.3.xx Marine
• Multi-line 2 - GPU v.3.xx Marine
• USW3 build version: 1056
• USW3 product database revision: 4805

Changes:

• Additional product database updated to support AGC-4 v.4.59.0.
• Alarm set point range of CIO 308 Pt100/Pt1000 inputs extended.
• Please note: Only the configuration files have changed.

New features:

• Support of CIO 116, CIO 208 and CIO 308
• Support of ALC-4 and ASC-4

Changes:

• Serial number made mandatory, in the option key generator.
• Product database updated to support AGC-4 v4.59.0
• Product database updated to support AGC 200 v4.59.0

Corrections:

• Voltmeter on device page corrected
• Buttons placed correctly in tree view
• AGC 100 "Counters and identifiers" issue corrected
• Various corrections to option N software

3.40.1

06/07/2016

40.1 06-07-2016

Changes:

• 1- Product database updated to support AGC-4 v4.57.0
• 2- Product database updated to support AGC 200 v4.57.0
• Please note: Only the configuration files have changed...
• 3.40.1 06-06-2016

Changes:

• Product database updated to support ASC PM Solar v5.06.0
• 3.40.1 31-05-2016

Changes:

• Product database updated to support AGC-4 v4.56.0
• Product database updated to support CGC 412 and CGC 413 v1.13.1
• Minor product database updates to AGC 252
• 3.40.1 21-12-2015 Changes:
• Added support for AGC 252

Corrections:

• PPM-3: In USW application configuration, two EDGs could be drawn, while only one EDG is supported in an application.
• Please note: Only the configuration files have changed...
  3.40.1 27-11-2015 

Changes:

• Updated Product Database for various products
• 3.40.1 01-07-2015 Corrections:
• USW 3.40 - F3 connection menu is not working for new users

3.40.0

24/06/2015

New features:

• Support of AFC PM (Automatic Fuel Controller).
• Support for Windows 8 - language selection.
• Support for 1/10000 in units.
• Translation tree. 

Changes:

• CAN line names - use of primary and secondary instead of A and B.
• Grey out of button for “activate plant configuration”, if only single unit application. 

Corrections:

• Russian language causes PDF export to fail.
• Parameter texts on shared channels updated correctly.
• Missing “edit notification” in list view, after parameter change in tree view.
• Translation issues for CGC 400, AGC 100 products.
• Missing connect icon in emulation mode.
• Digital status page not updated correctly.
• TB missing in USW 3.39.0 application supervision.
• GC-1F/2 ASW 2.31.1 Application configuration should not be visible.
• AGC-3 Dual mains application configuration is not working.
• TB appearing in old application drawing when shown in newer USW version.
• Batch read from M-Logic tab not successful.
• IP address – leading zeros.
• Chinese M-Logic PDF export.
• MB present when none is configured.
• AGC 100 emulation option problem.
• Import translation from file.

3.39.0

19/09/2014

Re-location of USW 3.39.0 - link to NTP-patch included

3.39.0 26-09-2014 NTP patch for USW 3.39.0

A patch is needed to make the NTP-configuration work.

In future releases this won’t be necessary.

3.39.0 26-09-2014 NTP patch for USW 3.39.0

A patch is needed to make the NTP-configuration work.

In future releases this won’t be necessary.

3.39.0 26-09-2014 Re-location of USW 3.39.0 - inclusive link to NTP-patch. 

New features:

• Support of ASC PM (Automatic Solar Controller).
• Support of Qc1103. 
• Support for firmware download to webarm hardware with new flashes mounted.
• Support for configuration of NTP in webarm from ver. 2.40.0.

 Changes:

• Possibility to change Loginfo scaling factor.
• Change of bit mask when writing inhibit configuration to device.

 Corrections:

• Access level update
• CGC 400 - missing Russian letters for translation 
• Russian language support now working 100%
• USW 3.38 usw files not recognised by Windows.
• PPM-3 cannot open batch files "File format error"

3.38.0

11/06/2014

New features:

• Update boot SW (Standard ML2 ver. 3 products)

Corrections:

• PPM-3 display of power measurement
• USW 3.37.0 freezes when connecting to PPM unit
• CGC 200: default parameters available before reading from device
• CGC 200: Parameter editor - dropdown list value selection

3.37.0

01/04/2014

New features:

• Support for extended Chinese characters in CGC 400
• Support of AGC PM product

Changes:

• Scaling in Trending - Default setup and possibility to choose alternative 

3.36.0

23/12/2013

New features:

• Parameters: Tree view for AGC 100 variants
• Parameters: Reloading of dependent parameters for AGC 100 variants
• Support of firmware upgrading over a TCP-IP connection if the AGC-4 is version 4.40, the option N has version 2.20 and the boot code has version 1.03.0
• Communication: Faster communication over TCP-IP if the option N has version 2.20
• Communication: Network parameter pop-up to easily set the IP address, netmask and gateway if the AGC-4 is version 4.40 and the option N is version 2.20
• Logs: Support of up to 500 alarms and event log lines
• Views: Tree view of the Views items
• Identifiers: Display of boot code and option N firmware version
• Identifiers: Display of production info like serial number, order number and production date

Corrections:

• Faster communication over USB when a parameter pop-up is open

3.35.0

30/08/2013

New features:

• Project Properties: Store user-defined comments as part of usw file 
• Project Properties: Display the firmware version from which the different components inside the usw file originate 
• Alarms: Double-click an alarm and open the corresponding parameter 
• Parameters: Alarm status is updated while a parameter popup is open 
• Parameters: Simultaneous display of multiple parameter popups 
• Parameters: Export/import of the list of favorite parameters 
• Parameters: Inhibits column added to the list view 
• Parameters: Favorite and Modified-Parameter filters work in tree view as well (AGC-4 and AGC 200) 
• Parameters: Reloading of dependent parameters (AGC-4 and AGC 200)
• Parameters: For selected parameters the Output A & B values are shown in the tree view mode (AGC-4 and AGC 200)
• Parameters: Display the parameters for the AGC 200 in a tree-like structure 
• Logs: Open .sdl files originating from the flashcard in AGC 200 
• New USB driver for CGC 200 and CGC 400 variants. 

Corrections:

• The application retrieved during the initial connection to GCU 112 does not cause an error message
• Identifier texts with Unicode characters are not written correctly to AGC 200 products

3.34.1

08/05/2013

Corrections:

• The firmware flashing of the CGC 200 works on all PCs
• Scaling is working correctly for controllers configured to different power and voltage scalings
• Cos phi is removed from the Electrical data window for PPM controllers
• The apparent power (S) in the Electrical data window is correct for PPM controllers
• The offline Batch-read procedure is working correctly
• The data fields in the Electrical data no longer appear to be editable

3.34.0

20/03/2013

New features:

• Support of the CGC 200 and CGC 400 variants
• Support of the AGC 100 variants
• Support of the AGC 200 firmware 4.21
• Support of the ECU 100 and GCU 100 variants
• Install script updated:
  a) shows EULA
  b) displays the USB installation popups sequentially
  c) CGC 200 USB driver added
• Supervision: Display of all available electrical data for the controllers in the application
• Supervision: Emulation support in a broad range of products (AGC 100, AGC 200 firmware >= 4.21,ECU and GCU 100 variants)
• Supervision: Save a screen copy to a graphical file 
• Supervision: Plant settings popup for easy access to parameters often changed after commissioning (applies only for AGC-4 and AGC 200 variants)
• Parameters: Display of parameters in a tree-like structure (applies only for AGC-4 variants and CGC 200)
• Alarms: Acknowledge of alarms individually
• Chinese localisation

Changes:

• Connecting to device procedure is more intuitive
• Alarms: Display of current alarms and alarm history

Corrections:

• The writing of Translations has been improved
• M-Logic and AOP lines have a consistent numbering in the relevant popups
• Read logs from GC-1F no longer fail

3.33.0

09/10/2012

New features

• Support of redundancy (AGC-4 only)
• Indication of the parameters that have been changed since commissioning (AGC-4 only)
• Display in Appl. Supervision of the names assigned to engines, breakers and mains (AGC-4 only)
• Possibility to reset logs in the controller (AGC-4 and AGC 200 only)

Changes

• M-logic page is empty initially
• M-Logic page adjusts to the width of the window
• Device page can handle negative power values

Corrections

• Batch write issue regarding Modbus configurator data was fixed
• Application Configuration page does not show “AGC” in the header initially
• Service level user can change the access level of any parameter to any lower level
• Data tracer will show the same number of digits as in the Trending window

3.32.0

07/06/2012

Install script updated to remove temporary files, which can cause problems during installation 

New features:

• The Connect Symbols are shown in Application Supervision to indicate the connected controller
• The texts assigned to digital inputs are shown in the Emulation inside Application Supervision
• Printout of Engine and Genset data in Application Supervision
• Applications are presented in tabs in Application Configuration
• Improved user interface to perform activation and broadcasts of applications
• Customisation of column widths in Parameter and Translations pages
• Execution of selected functions at the Windows Command prompt
• Automatic adjustment to the baud rate of the controller
• Faster batch writing of languages as those not translated are skipped
• Parameters can be tagged as favorites and a favorite filtering in the Parameter list can be applied
• The access level can be changed for a selected list of parameters
• Which columns to show and the sequence of these can be customised in the Parameters page
• Only enabled M-logic lines are shown on printouts
• Counter and Identifiers information can be printed

Changes:

• Properties of the following products were updated: AGC-3, AGC 200, PPM-3, AGC-4, GC-1F/2, PPU-3, PPM-3, GPU-3, GPC-3, GPU-3 REC, APU 264

Corrections:

• For the PPM-3 the terminal numbers given in the I/O page are correct
• Only Modbus ids in the range 1..247 are allowed
• Various improvements in the Color Scheme Editor in Supervision
• The configuration made with the Modbus Configurator can be stored as part of an usw file
• Breaker in Device page of APU 264 is updated correctly
• Older PPM-3 firmware no longer cause errors in USW 3
• Choosing the language to activate after doing translations also works with TCP-IP connection

3.30.1

07/12/2011

Changes:

• Supervision page is updated consistently according to active application.
• Batch read/write improved when offline.
• The correct access levels are applied for GC-1F.
• Edition of Energy counters improved.
• USW no longer claims exclusive access right to files.

3.30.0

08/11/2011

New features

• Support of the new controller AGC-4
• Counters: read-out of various counter values from the controller
• Identifiers: read-out of various id’s used the controller
• Dynamic M-Logic evaluation: the values for the M-Logic lines are evaluated on-the-fly
• AOP and M-Logic lines in use: provide an overview of where different event types are used in the logic lines
• Batch read: allows the read-out of logs and export to Excel file format
• Backup/restore: backup a controller for later restoring
• Translations: Prompt for selection of which language to set active after the writing of translations
• The language of the USW 3 application can be set to Russian
• Support for automatic reconnection after firmware flashing
• Display of all controller views at the same time
• A time offset used during synchronizing the time of the PC with the controller can be set
• Explicit scanning for available COM ports
• Emulation of a plant and response to e.g. inputs
• Deep dive allows to navigate between the upper and lower levels of option G7 based plants
• Permission: control which access levels can do what
• Display of the engine data retrieved over j1939 by the controller

Changes

• Only buttons and menus relevant for the offline situation are shown at startup of the USW 3
• During batch read/write the sequence of items is changed
• The help functionality has been updated with the new features listed below
• An issue regarding the sending of emails and/or SMS’s from the N-option is fixed
• In offline mode the Device page corresponding to a open file is shown
• User is prohibited to enter invalid IP address in the N-Option application
• Setting of the trending update rate is fixed
• The offline writing of view is no longer, mistakenly, reported as successful
• Logs: order of first two columns Timestamp and Text is switched so Timestamp goes first

3.21.0

15/04/2011

• New features
• AOP, Views and I/O Settings buttons in the top toolbar are active if connected to a device or an USW file with corresponding information is loaded.
• Support of GPU-3 REC
• Support of GC-1F ATS
• Support of AGC 222
• Support of various new parameters in PPM 3.05
• The application Modbus Configurator is added as part of the USW installation. This  application is used to perform a memory mapping to the configurable memory area in the devices.
• Application Settings: Functions to clear the settings that the USW saves from  session to session
• Option Wizard: Last entered customer information is displayed as default
• Project properties: Option- and hardware configuration can be copied to clipboard
• In Batch Read/Write a new shortcut, Ctrl-A, selects all items Changes
• Translations written from a Chinese PC: the issue, where the character "?" was  shown in GC-1F variants is fixed.
• Terminal numbers in the Inputs/Outputs page are corrected for AGC-3.
• Application Configuration is handled before Parameters during Batch Read/Write operations.
• Cyrillic K (К) handled properly
• Removal of “Generate random data”
• Supervision: “Engine data” was renamed to “Genset data”
• Writing of the netmask (AGC2xx products) is fixed.
• M-Logic dropdowns are always repopulated when connecting to another device type
• When logs are exported to Excel also the timestamps are saved in the file

3.20.0

04/02/2011

New features

• Support of the new product GC-1F/2
• Support of the new products APU-3, APU 264
• Move and copy items in M-Logic
• List of existing ports is displayed in communication setting popup
• Connectivity check in Supervision (require AGC firmware 3.6 and above)
• Compatibility check in Supervision (require AGC firmware 3.6 and above)
• Engine data in Supervision (require AGC firmware 3.6 and above)
• Cyrillic display option (CYD) shown in Options
• Terminal numbers shown in Input/Outputs
• Tooltip texts for parameters
• USW files can be shared among selected products series:
• AGC 212, 213, 232, 242, 243
• AGC 245, 246
• GC-1F and GC-1F/2
• List of keyboard shortcuts is extended
• Subnet mask can be edited for AGC 200 series if supported by product (require AGC firmware 3.6 and above)
• Device flashing and clock synchronization as part of the optional batch write steps.

Changes

• Improved scaling in the Device page of PPU-3, GPU-3, GPC-3, GPC-3 Hydro
• Updated Help functionality
• Installation on Windows 7 does not require administrative rights
• More intuitive tabing order in M-Logic
• Colour scheme editor and color scheme selection joined in the same popup
• Improved scaling of meters on Device page for GC-1F

3.16.0

24/08/2010

New features

• Import translations from file into selectable columns in Translations.
• Assign language names to translations columns.
• Change the sequence of the language columns in Translations.
• Copy language columns to other columns in Translations.
• Full 64 bit support:
• Signed USB driver for AGC 200 for 32 and 64 bit Windows platforms (XP, Vista and 7).
• Signed USB driver for AGC-3, PPM-3, PPU-3, GPU-3, GPC-3, GPU-3 Hydro for 32 and 64 bit Windows platforms (XP, Vista and 7)
• Drag-‘n-drop of USW file onto the USW application.
• Led or button number is shown in the header of the AOP item popup.
• User confirmation when writing AOP1, AOP2 or M-Logic.

Changes

• Updated Option wizard.
• Improved support of translations in AGC 200 series.
• Improved writing of translations.
• Improved support of Applications with a ring-shaped bus-bar.
• Improved error handling during writing of translations to GC-1F.
• Support of PPM 3.04.
• Support of new parameters for PPU-3, GPC-3, GPU-3, GPU-3 Hydro.
• Updated Help functionality.

3.15.1

07/05/2010

Changes (USW 3.15.1)

• Writing of M-Logic, AOP1 and AOP2 configurations are password protected.
• Enabled flags are written correctly when writing parameters.
• New features (USW 3.15.0)
• Support of AGC 200 variants which includes:
• Unicode text support in Translations
• Retrieval of logs
• Firmware upgrading
• Configuration of TCP/IP network parameters
• New USB driver
• Export of reports to PDF
• Support of voltage and power scaling in PPU3, GPU 3 and GPC 3
• M-Logic/AOP improvements:
• Color symbol to indicate the Enabled state of each line
• Optional user-defined description field for each line
• IP address edited in Settings dialog box through combobox with auto completion
• Plant Option dialog box: In offline mode the Product type is selected from a list of product families
• Batch Read/Write can be cancelled
• Save Application Configuration to jpeg file
• Installation file is digitally signed

Changes (USW 3.15.0)

• Increased Parameter writing speed
• Single DB application colored correctly
• Batch jobs: The caption shows whether it is a read or write batch job
• Improved export to Excel file format (content and format)
• Improved device filtering to prohibit writing of parameters from one device type to another
• Writing of M-Logic, AOP1 and AOP2 configurations are password protected
• Number of languages written in Translations cannot exceed the max allowed by the device
• Ring connected busbar is handled consistently

3.15.0

05/05/2010

New features

• Support of AGC 200 variants which includes:
• Unicode text support in Translations
• Retrieval of logs
• Firmware upgrading
• Configuration of TCP/IP network parameters
• New USB driver
• Export of reports to PDF
• Support of voltage and power scaling in PPU3, GPU 3 and GPC 3
• M-Logic/AOP improvements:
• Color symbol to indicate the Enabled state of each line
• Optional user-defined description field for each line
• IP address edited in Settings dialog box through combobox with auto completion
• Plant Option dialog box: In offline mode the Product type is selected from a list of product families
• Batch Read/Write can be cancelled
• Save Application Configuration to jpeg file
• Installation file is digitally signed

Changes

• Increased Parameter writing speed
• Single DB application colored correctly
• Batch jobs: The caption shows whether it is a read or write batch job
• Improved export to Excel file format (content and format)
• Improved device filtering to prohibit writing of parameters from one device type to another
• Writing of M-Logic, AOP1 and AOP2 configurations are password protected
• Number of languages written in Translations cannot exceed the max allowed by the device
• Ring connected busbar is handled consistently

3.14.0

28/12/2009

New features:

• Support of AGC 3.50
• Support of PPM 3.03
• Support of PPU 3.00.1 and its variants
• Support of New N-Option board (M1)
• M-Logic items collapsible/expandable
• Device ID visible on the status bar
• Connected device versus USW file compatibility check

Changes: 

• Dedicated GPU Hydro device overview
• Supervision legend improved
• Colour Scheme Editor in Supervision improved
• Improvements to Translations 
• Improved high alarm handling when using an older USW file
• N-option button only shown for supporting devices

3.13.0

15/10/2009

New features:

• Support of PPU3 and its variants.
• Search facility on the Parameters view.
• File association and distinctive icon for USW files.
• Dynamic legend on the Application Supervision view.
• Adjustable Polling delay for TCP-IP communication.

Changes:

• Performance boost in M-Logic loading.
• Parameters view improvements.
• Translations view: Extended Character dialog improved.
• Support of 20 configurable views in the AGC 3.4xx 
• Plant view for the gen-set mode “Mains Power Export” improved.

3.12.1

13/07/2009

Changes:

• Support of AGC 3.41

3.12.0

15/06/2009

New features: 

• Application configuration and Supervision works with up to 256 Gen-sets as supported by the G7 option in AGC 3.40 
• In Application Supervision three colors are used to indicate the state of the Gen-sets and bus-bars 
• Device IDs can be changed in Application Configuration 
• Support of TCP-IP Modbus communication through gateway to AGC or PPM without N-option card. 
• New command line parameter BATCHWRITE, which perform a batch write operation with the project file provided by the argument of the OPENFILE parameter 

Changes: 

• Enhancement of translations reading: Only available translations in the device are retrieved instead of all translations. 
• Printing an application configuration from the USW will no longer cause it to close. 
• When some multi-inputs are configured to digital inputs, their statuses are now updated in the Inputs/Outputs view. 
• Various fixes and enhancements in Trending. 
• Printing of translated strings is fixed. 
• The USW version is shown in the title bar 

3.11.1

24/03/2009

New features: 

• User-customizable Read/Write timeouts: The connection-settings dialog allows the end-user to adjust various read/write timeouts. 

Changes: 

• Support for PPM - 3.01.0. 
• If a firmware upgrade fails, it is not possible to repeat this operation when the display shows “BOOT MODE, FLASH ERASED” (this applies only to USW 3.11.0).

3.11.0

18/02/2009

New Features

• Improved PPM support 

Corrections

• Improvements in “Application configuration” 
• Modification of “Enable” and “High alarm” columns in the parameter list 
• Minor improvements to the plant view 
• Scaling of plant view instruments at high voltage values improved 
• Communication status improved 
• Trending improvements 

3.10.2

03/10/2008

New features:

• Added support for installation of new firmware for the AGC/PPM N-Options.

Changes:

• Improved stability of the Modbus TCP/IP interface.
• Max tags in the N-Option feature ‘Advanced logging’ changed to 48.

3.10.1

18/07/2008

New features:

• Clicking on the logo at the top of the navigation bar will bring you to our homepage
• Outputs A & B are now shown as explicit texts in the parameter window and the printout
• After synchronization of the translations, untranslated and already translated texts are clearly indicated

Changes:

• The commissioning panel is now active regardless of the value of the timer
• Writing a parameter file via a “batch write” will trigger a consistency check when appropriate

Corrections:

• Status when performing a “batch read” operation updated
• Two fail class groups could appear when configuring an AOP
• Button 2 on an AOP template was not aligned correctly
• Behavior of the translations synchronization updated
• Error message when leaving the translations window removed

3.10.0

30/06/2008

New features:

• Plant configuration and supervision (AGC 3.30)

Changes:

• Translation: Improvements in visualization and mask handling.
• Recently used file list handling updated.
• Placement of meters in AGC Dual main configuration adjusted.
• Input/Output window handling.

Corrections:

• Trending: Gain on some values adjusted.
• Data tracer: Handling of ‘Unit names’
• Firmware download recovery mode.

3.00.30

19/03/2008

•  Backward compatibility improved for ‘.usw’-files including languages.

3.00.29

05/03/2008

New features:

• Translations are now part of batch operations.
• Support of all fonts/charsets (Display unit european and cyrillic, graphical display european/cyrillic and limited european/chinese).
• Extended characters dialog redesigned.
• Font selection dialog added (graphical display only).
• Baud rate negociated with the unit (GC-1F only) up to 115200 bauds.
• Communication type shown on the status bar (serial COMx, TCP-IP IP: x.x.x.x).
• Application software/firmware file extension automatically selected according to the connected unit.

Corrections:

• Batch read/write: All AOP2s (ID 1 to 5) are readen/written instead of AOP2 ID 1 only.
• Parameters: When sending parameters stored in a project file, some parameter settings (configuration bits) could be overwritten in the unit.
• Parameters: Some items on the categories tab sheet could not be reached with mouse.
• Project file properties: Some hardware items could be duplicated.
• About window: Centered on the main monitor instead of the desktop (dual monitor systems).

3.00.27

11/10/2007

Correction:

• This USW release circumvents an issue present in the AGC firmware between release 3.10.2 and 3.21.0, where some parameters would not appear on the parameter list as expected.

3.00.26

20/09/2007

New features:

• The parameter inhibits are now shown on the parameter printout (only for parameters having inhibits defined).
• Parameter printout changed a bit (alternate colors).
• AOP1/2: Possibility to name individually leds and buttons (information saved in project file).

Changes:

• AOP1/2: Leds and buttons drawing changed slightly. M-Logic rule enabled -> white background. M-Logic rule not enabled -> hatched white background.
• Parameter filtering modified.

Corrections:

• When working on a saved parameter file (in a project file), and when editing a parameter, relays could appear as transducers.
• Faulty dependency check in I/O settings when working offline (information was based its dependencies on the device information).

3.00.25

13/07/2007

• List of the most recently used project files added.
• Writing of translations improved
• Offline configuration of the AOP-1 and -2 improved

3.00.24

26/06/2007

• Batch upload/download officially introduced (not in preview anymore).
• Save As feature
• Possibility to print all reports in A4 or Letter
• Option upgrade order form is now in english only
• AOP 1/2 printout refined
• Possibility to choose Modbus serial or TCP-IP
• Changes in the product database
• N-Option configurator

3.00.21

30/04/2007

• Changes for GC-1F.

3.0.0.20

23/02/2007

• Support of GC-1F product.

3.0.0.19

01/02/2007

• Support of the latest AGC release 3.1. 
• Usability of the parameter category filtering improved.
• Project file handling enhanced.
• Help file format changed.

3.0.0.18

17/10/2006

• First release

3.31.0

Changes

• Product updates: AGC-3, AGC 200, PPM-3, PPU-3, GPU-3, GPC-3, GPU-3 REC, GC-1F/2, AGC-4
• OEM options are removed from the Options page.
• OEM options are removed from the Option wizard.
• The user access level required for performing an update of the controller firmware of a GC- 1F is changed to "Customer".
• The keyboard shortcut “Alt+Tab” allows navigation back and forth between the USW and other  applications even when a popup is open
• Trending allows only realistic sample rates.

New features

• The Modbus Configurator (to set up the configurable memory area) is built into the USW
• Modbus configuration is included in the Batch Read/Write
• Notification sounds in case of alarms and batch operations.
• Custom logo can be used on printouts
• Broadcast progress is indicated in Application Configuration and Application Supervision (if supported by controller)
• New permission rule that prevents the user to see parameters that cannot be edited at  current access level