Multi-line 300 PICUS ver. 1.x.x.

1.0.9.3

23/10/2019

Changes

 Important usability and optimisation of these features:

• Connectivity to controllers
• Upgrade of firmware/BSP

1.0.9.1

17/06/2019

Changes

 Important usability and optimization of these features:

• Connectivity to controllers
• Upgrade of firmware/BSP
• Initial download
• Initial download after BSP update failure

1.0.9.0

01/02/2019

Changes:

• To support BTB redundant breaker feedback.

1.0.8.1

10/01/2019

Changes:

• Enabling logon button in the offline folder with REST 1.0.2.0
• Support of "output functions" from a backup file
• Support of DISCLAIMER pop-up consistency in PICUS
• Support of custom curves with decimals in PICUS
• Support of CODESYS in PICUS: PPU 300 v.1.0.8.0

1.0.8.0

01/10/2018

New features:

• NTP configuration and date time settings
• New HMI for backup and restore  

Changes:

• Support of BSP 3.0.0.0 update for DU 300
• Support minimum/maximum values on livedata screen and show scale value
• Support of backup folder in offline mode.

1.0.7.0

22/03/2018

New features:

• Support of regulator status (GOV/AVR screen).

Changes:

• Warning message mismatch on 'supervision' and 'single line' screen is changed.
• Backward compatibility check for all the released versions and future releases of the ML 300 product is implemented.

1.0.6.0

09/02/2018

New features: 

• Support of compare and operator element in CustomLogic on relevant products.
• Support of mains and genset type on relevant products..
• Support of graph parameters on relevant products.

Changes:

• Corrections for scaling and precision.
• Mains power measurement added to supervision page.
• Problem with restoring backup from old SW to new SW.
• PICUS stopped working when changing controller type.
• PICUS would not connect to the PPM 300 with Chinese text.
• Event log was not telling which "command" (button) was pressed.

1.0.5.0

01/11/2017

1.0.4.0

15/08/2017

1.0.3.1

06/03/2017

This software applies to the following DEIF products:

• Multi-line 300, PPU 300
• Multi-line 300, PPM 300
• Multi-line 300, GPU 300

Change:
- When using two EIM3.1 modules in one controller, the terminals for the magnetic pickup are only active in the first EIM3.1 module.

1.0.3.0

21/02/2017

This software applies to the following DEIF products:

• Multi-line 300, PPU 300
• Multi-line 300, PPM 300
• Multi-line 300, GPU 300
  
   

New features:

• Changes in broadcasting Single line diagram.
• Optimization in firmware update procedure.
• Bug fixes and usability improvements.

Changes:

• Remove Time Zone selection field from Date and time screen in PICUS
• PICUS AI & AO - curve points + / - become difficult to use
• Pop-up to allow to broadcast to controllers that are not safe for commissioning
• Show all controllers in the broadcast list in the single line creator page
• Remove write button in the single line creator page
• As a commissioning engineer, I need to be able to broadcast single line drawings even though one or more controllers are not ready
• Controller should delete lock in case of success or failure during fw/os update from PICUS
• PICUS should suppress notification during fw/os update
• PICUS r5515 - IO now refreshes displayed setting upon WRITE
• Parameters not shown in Emulation Load box (user-friendliness)

1.0.2.0

22/12/2016

New features:

• Support for PPU 300 in PICUS

Changes:

• Removed the safe for commissioning control under single line creator
• The regulator mode "Fixed Frequency" has activate written twice in display and Picus
• Check backward REST compatibility in PICUS.
• In the single line creator, the "Init" button is renamed to "New"
• Progress indication not shown properly while updating multiple controllers when packet contains BSP and application software
• PICUS have version comparison before starting OS update
• PICUS have internal check whether to start update in parallel or serial manner
• Implement Multi-line pop-up in PICUS
• Support of 4 line pop-up in the display
• Users to see parameter numbers
• Remove latch pop-up in PICUS
• Using PICUS Firmware Update Parallel
• PICUS offline local file adds local folder one time
• Livedata and Plant Supervision visible in permission page
• External breakers
• Support for passwords in offline projects
• Mixed access in group settings
• Check REST backward compatibility in PICUS
• PICUS can broadcast new plant
• Test and validate support of Windows 10
• Popup with meaningful texts to guide the user in case the user is doing anything wrong
• The terminal name to indicate what the terminal is used for

1.0.12.1

03/08/2020

Bug fixes :

• Various usability improvements
• Fixed issue with conversion of US units

1.0.12.0

09/06/2020

New features:

• Support of IOM3.2 and IOM3.3.

Bug fixes :

• Different checkbox in the above/below range in PICUS.
• Different font in the minimized/maximised window in PICUS.
• Report was not showing the selected Compensation information.
• Description in CustomLogic on internal variables was not updated.
• Edit of BITMAP address in the Modbus configuration was not working.
• Issue with saving the Modbus protocol made in PICUS.
• PICUS was not always showing Path in the Modbus list.
• PICUS was not getting values in the Modbus configurator.
• PICUS would freeze after the network was lost during backup.
• It was not possible to set precision for custom scales for analogue Input and analogue output in PICUS.

1.0.11.1

01/05/2020

Corrections:

• Improvements in Initial download functionality for ML 300 controllers and DU 300 display units. 
• Improvements and optimization in the BSP update procedure.

1.0.11.0

04/04/2020

New features:

• Support of Ethernet configuration.
• Support of configuration of network ports.

Corrections:

• Permissions were not updated automatically the first time after a software update.
• No warning from PICUS when configuring the same input in an extension rack and a master controller.
• Modbus text was missing in the new feature Custom parameter.

1.0.10.2

12/02/2020

Corrections:

• Various usability improvements.
• Fixed a problem with supervision data not updating.
• Fixed an issue with multiple error messages while closing PICUS.

1.0.10.0

13/12/2019

New features:

• Acknowledge all alarms.
• Individual alarm test.
• Extended alarm Information.
• Broadcast of single or set of parameters.
• Support of conversion of old backup folder to .config format.
• Support of conversion of old .backup file to a folder.
• Support of editing offline files.
• Commissioning report.
• Support of create, configure and update Modbus protocols, servers and conversions.
• Support of input/output extension units, including 4 and 7 racks.
• Configuration and supervision of fieldbus.
• Support of showing different software versions.
• Support of selecting controller language.

Changes:

• Information on why the controller is not ready for software update.
• Minimum 28 controllers in 1 SLD for Marine.
• Multiple PICUS versions on one computer.
• Various usability improvements.

Corrections:

• Connection problems in old PICUS versions.
• Corrections in firmware update procedure.
• Information pop-ups are not shown when a message box is active.
• Added graph parameters in reports.
• Wrong error message for missing CODESYS license.
• Menu options are not visible in PICUS.
• Not ready message in restore.
• Create backup from PPU 1.0.4.1 failed.
• PICUS does not log off when controller restarts.
• Restore from old backup. Misleading text confusing the users.
• Error message "Invalid pointer operation" when closing PICUS.
• PICUS don't hide message box after disconnecting the controller.
• BSP versions missing on connect page.
• Not possible to read out CustomLogic element description in Report.
• Parameter page size does not match when minimising window.

1.0.1.0

30/09/2016

New features:

• Creating and maintaining of permissions.
• Configuring and commissioning.
• CustomLogic.
• Creating and maintaining of the single-line diagram.
• Sending commands.
• Supervision (read out) of data and information.
• Livedata information.
• Alarm handling.
• Emulation of the system.
• Updating and applying firmware.
• Creating and restoring backup files.
• Working on an offline project.
• Configuring of Analog IOs

Works on the following OS:

• Windows 7, 8.1

Disclaimer:

>>> The "Shelve" and "Out of Service" alarm time function is working correctly when sent from the DU 300 display. If sent from PICUS the controller will act unpredictable <<<